Product: Banksia Roll Top Weldmesh Panel

Description: 900mm x 3000mm, 5mm solid vertical bars spaced 75mm apart, 2 x solid 5mm horizontal centre bars spaced 75mm apart

Price: $65 inc GST

Available Finish: Galvanised. Powder coating available at extra cost

Product: Banksia Roll Top Weldmesh Panel

Description: 1200mm x 3000mm, 5mm solid vertical bars spaced 75mm apart, 2 x solid 5mm horizontal centre bars spaced 75mm apart

Price: $69 inc GST

Available Finish: Galvanised. Powder coating available at extra cost 

Product: Banksia Single Gate Kit

Description: 955mm wide (to suit an opening of 995mm between posts), gate kit comes complete with 1 x pair of hinges, 1 x D latch & striker 

Price: $145 inc GST (900mm high)

Price: $155 inc GST (1200mm high)

Available Finish: Galvanised. Powder coating available at extra cost  

Please Note: Size of gate can vary.  Always measure gate before installing posts.  The opening between posts needs to be 40mm wider than actual gate width.

Product: Acacia Roll Top Weldmesh Panel

Description: 900mm x 3000mm, 4mm solid vertical bars spaced 75mm apart, 4mm solid horizontal bars spaced 50mm apart

Price: $65 inc GST

Available Finish: Galvanised. Powder coating available at extra cost

Product: Acacia Roll Top Weldmesh Panel

Description: 1200mm x 3000mm, 4mm solid vertical bars spaced 75mm apart, 4mm solid horizontal bars spaced 50mm apart

Price: $69 inc GST

Available Finish: Galvanised. Powder coating available at extra cost

Product: Acacia Single Gate Kit

Description: 955mm wide (to suit an opening of 995mm between posts), gate kit comes complete with 1 x pair of hinges, 1 x D latch & striker 

Price: $145 inc GST (900mm high)

Price: $155 inc GST (1200mm high)

Available Finish: Galvanised. Powder coating available at extra cost

Please Note: Size of gate can vary.  Always measure gate before installing posts.  The opening between posts needs to be 40mm wider than actual gate width.  

Product: Flat Weldmesh Handy Panel

Description: 1200mm x 2400mm flat sheet, 50mm x 50mm openings, 3.15mm wire thickness

Price: $35 inc GST 

Other sizes available: 25mm x 25mm x 2.5mm - $41 inc GST

                                              100mm x 100mm x 4mm - $39 inc GST

Available Finish: Galvanised. Powder coating available at extra cost

Product: Galvanised Steel Post

Description: 50mm x 50mm x 1500mm, 1.6mm wall thickness, includes 1 x plastic post cap.  For use with 900mm high Weldmesh panels & gates.

Price: $16 inc GST

Available Finish: Galvanised. Powder coating available at extra cost

Product: Galvanised Steel Post

Description: 50mm x 50mm x 1800mm, 1.6mm wall thickness, includes 1 x plastic post cap.  For use with 1200mm high Weldmesh panels & gates.

Price: $19 inc GST

Available Finish: Galvanised. Powder coating available at extra cost

Product: U-clip & Tek Screw Kit

Description: Galvanised U-clip x 6, galvanised 12-14x20 tek screw x 6.  For the installation of Weldmesh panels onto steel posts.

Price: $2.70 inc GST

Available Finish: Galvanised. Powder coating available at extra cost

 

Sloping block? No problem.

We can 'rake' the Banksia Roll Top Weldmesh panels to suit the slope of your ground, using our hydraulic raking table.

Typically the Banksia panels in either 900mm or 1200mm high can be 'raked' to 15 degrees (797mm fall over 3000mm)

PLEASE NOTE:  We can not 'rake' the Acacia roll top weldmesh panels

Roll top weldmesh panels are designed to give you a strong durable fence, that allows good vision through each panel to retain your view.  Weldmesh panels also tend to work very well in areas that are surrounded by plants & shrubs. 

There are 2 x main designs that are kept in stock.  The most commonly used style is the 'Banksia' panel, which is made from 5mm steel vertical bars that are spaced approx 75mm apart, with 2 x horizontal bars running through the middle of the panel also spaced at approx 75mm apart. 

The panels have a rolled top & bottom that gives the panel structural rigidity.

These panels are also ideal for sloping blocks, and can be 'raked' to suit the fall of your block.  Poole Enterprises & Fencing Pty Ltd have a hydraulic table that allows the 'Banksia' panel to be raked from level through to approx 15 degrees (797mm fall over 3000mm).    

The 2nd most commonly used panel is the 'Acacia' panel, which is made from 4mm steel vertical bars that are spaced approx 75mm apart, and 4mm horizontal bars spaced 50mm apart, giving the panel a grid effect with 75mm x 50mm sized holes.  These panels are great for enclosing small dogs.  These panels are no longer able to be 'raked'.

 

Copyright - Poole Enterprises & Fencing Pty Ltd 2017